| 12/2022 |
AFFINIS
|
Trueness of full-arch dental models obtained by digital and conventional impression techniques: an in vivo study
|
| 02/2020 |
PRESIDENT
|
Local accuracy of actual intraoral scanning systems for single-tooth preparations in vitro
|
| 10/2019 |
Magic FoamCord
|
A Comparative Evaluation of Efficacy of Gingival Retraction Using Polyvinyl Siloxane Foam Retraction System…
A Comparative Evaluation of Efficacy of Gingival Retraction Using Polyvinyl Siloxane Foam Retraction System, Vinyl Polysiloxane Paste Retraction System, and Copper Wire Reinforced Retraction Cord in Endodontically Treated Teeth: An in vivo Study
|
| 08/2019 |
AFFINIS
|
Moderne Werkstoffe zur Abformung und Bissregistrierung
|
| 05/2019 |
PRESIDENT
|
Accuracy of complete- and partial-arch impressions of actual intraoral scanning systems in vitro
|
| 08/2017 |
AFFINIS
|
A Comparative Analysis of Master Casts Obtained using Different Surface Treatments on Impression Copings for Single Tooth Implant Replacement - An In vitro Study
|
| 08/2017 |
AFFINIS
|
Accuracy of a separating foil impression using a novel polyolefin foil compared to a custom tray and a stock tray technique
|
| 11/2015 |
AFFINIS
|
Dimensional Stability of Two Polyvinyl Siloxane Impression Materials in Different Time Intervals
|
| 05/2015 |
PRESIDENT
|
Accuracy and precision of silicon based impression media for quantitative areal texture analysis
|
| 12/2014 |
AFFINIS
|
A Comparative Evaluation of Dimensional Accuracy and Surface Detail Reproduction of Four Hydrophilic Vinyl Polysiloxane Impression Materials Tested Under Dry, Moist, and Wet Conditions-An In Vitro Study
A Comparative Evaluation of Dimensional Accuracy
|
| 12/2014 |
AFFINIS
|
An evaluation of the fit of metal-ceramic restorations made with an autoclaved silicone-based impression material.
|
| 01/2014 |
AFFINIS
|
Analysis of autoclave induced dimensional changes on addition silicones
|
| 12/2013 |
AFFINIS
|
Evaluation of Dimensional Stability and Accuracy of Autoclavable Polyvinyl Siloxane Impression Material
|
| 06/2013 |
AFFINIS
|
Comparison of elastomeric impression materials' thixotropic behavior.
|
| 05/2013 |
AFFINIS
|
Surface Roughness of PVS IM Following Chemical Disinfection, Autoclave and Microwave Sterilization
|
| 08/2012 |
AFFINIS
|
Precision and Handling of A-silicon versus Polyether for Implant Impressions
|
| 03/2011 |
PRESIDENT
|
The dimensional stability of impression materials and its effect on in vitro tooth wear studies
|
| 01/2011 |
AFFINIS
|
Evaluation of Dimensional Stability of Autoclavable Elastomeric Impression Material
|
| 07/2010 |
AFFINIS
|
Effect of Autoclave Sterilisation on the Dimensional Stability and Tear Strength of Three Silicone Impression Materials
|
| 05/2007 |
AFFINIS
|
Quality of impressions using hydrophilic polyvinyl siloxane in a clinical study of 249 patients.
|
| 09/2004 |
AFFINIS
|
Accuracy of different polyvinylsiloxanes: A Clinical pilot study
|
| 08/2004 |
AFFINIS
|
Klinisch erreichbare Abformgenauigkeit von A-Silikonen
|
| 09/2003 |
PRESIDENT
|
The influence of handling on the elasticity of addition silicone putties
|
| 07/2003 |
AFFINIS
|
Selected Characteristics of a New Vinyl Polysiloxane Impression Material: A Randomized Clinical Trial
|
| 04/2001 |
PRESIDENT
|
Effect of wash bulk on the accuracy of polyvinyl siloxane putty-wash impressions
|
| 05/1999 |
AFFINIS
|
Dimensional stability of addition cured silicone impressions following autoclave sterlisation
|
| 11/1998 |
PRESIDENT
|
Rheological Properties of Elastomers Before and During Setting
|
| 08/1988 |
PRESIDENT
|
Review of Dental Impression Materials
|
| 02/1983 |
PRESIDENT
|
Curing contraction of addition-type silicone impression materials
|
| 12/1982 |
PRESIDENT
|
Thermal expansion of addition polymerization (Type II) silicone impression materials
|
